Dell Studio 1535 / 1536 / 1537 DVD Optical Drive Removal and Installation

Created by on April 12, 2011
PrintEmail

In this Dell laptop tutorial we are going to show you how to install and replace the DVD CD Optical Drive on your Dell Studio 1535 / 1536 / 1537 laptop. These installation instructions have be made into 16 easy to follow printable steps. We have also create a video tutorial that shows you how to install your Dell Studio 1535 / 1536 / 1537 DVD CD Optical Drive.

Before you begin

Please take the time read the following safety guidelines when working on static sensitive electrical components.
Dell repair manual service precautions

Tools needed for this laptop repair

  • 1 x small phillips head screw driver
  • 1 x small plastic scribe
Studio 1537 DVD Optical Drive

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Studio 1537 DVD Optical Drive

Video tutorial repair manual



Installation and Removal Instructions
Dell Studio 1535 / 1536 / 1537 DVD CD Optical Drive

Unscrew the 7 retaining screws.

Step 1

  • Remove the battery.
  • Unscrew the 7 retaining screws.
  • Remove the access panel door.
Unscrew the 7 retaining screws. Remove the access panel door.
Remove the (7) 2.5mm x 5mm screws on the bottom base assembly.

Step 2

  • Remove the screws under the battery.
  • Remove the (7) 2.5mm x 5mm screws on the bottom base assembly.
Remove the (7) 2.5mm x 5mm screws on the bottom base assembly. Remove the screws under the battery.
Turn the base assembly over and remove the optical drive screw.

Step 3

  • Turn the base assembly over and remove the optical drive screw.
Loosen the cables from the routing tabs.

Step 4

  • Turn over the laptop and disconnect the WIFI antenna cables.
  • Loosen the cables from the routing tabs.
Loosen the cables from the routing tabs. Turn over the laptop and disconnect the WIFI antenna cables.
Remove the (2) 2.5mm x 5mm screws holding the hinges to the base.

Step 5

  • Remove the (2) 2.5mm x 5mm screws holding the hinges to the base.
Carefully lift the Center Control Media Buttons Cover away form the base. You should start unsnapping it at the LCD display side being careful not to lift to fast so the cable doesn’t break.

Step 6

  • Open the laptop screen as wide as possible.
  • Carefully lift the Center Control Media Buttons Cover away form the base. You should start unsnapping it at the LCD display side being careful not to lift to fast so the cable doesn’t break.
Remove the Keyboard Trim Plastic. Start by lifting the plastic at the top corner and working your way around the keyboard.

Step 7

  • Leave the Center Control Media Buttons Cover loose.
  • Remove the Keyboard Trim Plastic. Start by lifting the plastic at the top corner and working your way around the keyboard.
Carefully lift the cable latch and unhook the cable.

Step 8

  • Unscrew the (2) 2mm x 3mm screws holding the keyboard to the base and gently flip the keyboard over. Be cautious, lifting the keyboard with the cable connected, it is possible to break the latch if you pull it too hard.
  • Carefully lift the cable latch and unhook the cable.
Carefully lift the cable latch and unhook the cable. Unscrew the (2) 2mm x 3mm screws holding the keyboard to the base and gently flip the keyboard over. Be cautious, lifting the keyboard with the cable connected, it is possible to break the latch if you pull it too hard.
Carefully lift the Center Control Media Buttons Cover cable latch and remove the Center Control Media Buttons Cover.

Step 9

  • Carefully lift the Center Control Media Buttons Cover cable latch and remove the Center Control Media Buttons Cover.
Pull the WIFI cables through the motherboard routing hole.

Step 10

  • Disconnect the LCD Cable, the Camera Cable, and the Power Button Cable.
  • Pull the WIFI cables through the motherboard routing hole.
  • Loosen all of the cables and remove them from there routing channels.
Pull the WIFI cables through the motherboard routing hole. Loosen all of the cables and remove them from there routing channels.Disconnect the LCD Cable, the Camera Cable, and the Power Button Cable.
Unscrew the right side 2.5mm x 5mm hinge screw.

Step 11

  • Unscrew the left side 2.5mm x 5mm hinge screw.
  • Unscrew the right side 2.5mm x 5mm hinge screw.
Unscrew the right side 2.5mm x 5mm hinge screw. Unscrew the left side 2.5mm x 5mm hinge screw.
Lift the LCD Display assembly off of the base.

Step 12

  • Lift the LCD Display assembly off of the base.
Remove the remaining (4) 2.5mm x 5mm screws.

Step 13

  • Remove the (3) 2mm x 3mm screws.
  • Remove the remaining (4) 2.5mm x 5mm screws.
Remove the remaining (4) 2.5mm x 5mm screws. Remove the (3) 2mm x 3mm screws.
Unplug the (3) palmrest cables.

Step 14

  • Unplug the (3) palmrest cables.
Lift the palmrest from the base assembly.

Step 15

  • Lift the palmrest from the base assembly.
Lift the optical drive away from the motherboard.

Step 16

  • Turn the base right side up and remove the remaining optical drive screw.
  • Lift the optical drive away from the motherboard.
Lift the optical drive away from the motherboard. Turn the base right side up and remove the remaining optical drive screw.
Studio 1537 DVD Optical Drive

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Studio 1537 DVD Optical Drive

Topics: Dell Studio 1535/1536/1537 Repair Manual Dell Laptop Repair Dell Repair Manuals DVD Optical Drive DVD Optical Drive DVD Optical Drive Studio 1535 Studio 1536 Studio 1537

Tags

Join the conversation!

2 Responses to Dell Studio 1535 / 1536 / 1537 DVD Optical Drive Removal and Installation

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.