Dell XPS M1330 LCD Display Rail Removal and Installation

Created by Roscoe Dyer on July 6, 2011

In this Dell laptop tutorial we are going to show you how to install and replace the LCD Display Rail on your Dell XPS M1330 laptop. These installation instructions have be made into 13 easy to follow printable steps. We have also create a video tutorial that shows you how to install your Dell XPS M1330 LCD Display Rail.

Before you begin

Please take the time read the following safety guidelines when working on static sensitive electrical components.
Dell repair manual service precautions

Tools needed for this laptop repair

1 x small phillips head screwdriver
1 x small flat head screwdriver
1 x small plastic scribe

XPS M1330 LCD Mounting Rail

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!

Use this coupon code to save 5% off these parts

DIYM514

XPS M1330 LCD Mounting Rail

Video tutorial repair manual

Installation and Removal Instructions
Dell XPS M1330 LCD Display Rail

Step 1

Flip the laptop over and slide the battery clip to the left.
Slide the battery away from the laptop.

Step 2

Unscrew the wifi door retaining screw.
Lift the door from the base.

Step 3

Unscrew the (1) 2.5mm x 5mm screw.
Loosen the 3 memory door screws.
Lift the memory door off of the base.

On the bottom of the laptop, loosen the wireless antenna cables and unscrew the 2.5mm x 5mm left and right hinge screws.

Step 4

On the bottom of the laptop, loosen the wireless antenna cables and unscrew the 2.5mm x 5mm left and right hinge screws.

Open the laptop screen as wide as possible.

Step 5

Unscrew the (2) 2mm x 3mm screws below the battery.
Open the laptop screen as wide as possible.
Carefully lift the Center Control Media Buttons Cover away form the base. You should start unsnapping it at the LCD display side being careful not to lift to fast so the cable doesn’t break.

Unscrew the (2) 2mm x 2mm x 7mm wafer screws holding the keyboard to the base and gently flip the keyboard over. Be cautious, lifting the keyboard with the cable connected, it is possible to break the latch if you pull it too hard.

Step 6

Leave the Center Control Media Buttons Cover loose.
Unscrew the (2) 2mm x 2mm x 7mm wafer screws holding the keyboard to the base and gently flip the keyboard over. Be cautious, lifting the keyboard with the cable connected, it is possible to break the latch if you pull it too hard.

Carefully lift the cable latch and unhook the cable.

Step 7

Carefully lift the cable latch and unhook the cable.

Lift the Power Button Cover from the laptop.

Step 8

Carefully slide the Power Button Cover cable latch and remove the Power Button Cover Cable.
Lift the Power Button Cover from the laptop.

Disconnect the Camera cable, the LCD Display cable, and pull the wireless antenna cables through the motherboard.

Step 9

Disconnect the Camera cable, the LCD Display cable, and pull the wireless antenna cables through the motherboard.

Unscrew the 2.5mm x 5mm right hinge screw.

Step 10

Unscrew the 2.5mm x 5mm left hinge screw.
Unscrew the 2.5mm x 5mm right hinge screw.

Lift the LCD display assembly away from the laptop base.

Step 11

Lift the LCD display assembly away from the laptop base.

**It is usually easiest starting from the bottom of the screen, working your finger around the edge until it’s completely off. Watch for sharp edges that can cut your fingers.

Step 12

Open the screen as wide as possible and unsnap the bezel.
**It is usually easiest starting from the bottom of the screen, working your finger around the edge until it’s completely off. Watch for sharp edges that can cut your fingers.