$100 Diagnosis and Repair Parts-People has been specializing in Dell laptops for 20 years. We are a leading supplier of Dell replacement parts and stock all laptop repair parts needed to repair your Dell laptop. We are a trusted supplier to 1000s of schools, government agencies, military and repair shops worldwide. Send your laptop to the Dell Experts!
Most of our orders are from repeat customers. Parts-People began as a small company 20 years ago in an extra bedroom of my house. I had saved a small sum of money to purchase some computer parts and began selling them on eBay. After a few months I realized that people needed a place to go for Dell parts so I began building our website. Since we are located in Austin, Texas, where Dell.com was founded, I was able to set up a solid supply line with Dell. From the start, we focused on customer satisfaction and selling quality parts. We have grown a lot since 2002 but still and always the customer will come first. You will find that we go above and beyond with every order and offer free resources and support before and after the sale.
20 years in business
over 2 million Dell parts sold
In this Dell laptop tutorial we are going to show you how to install and replace the Palmrest on your Dell Inspiron 1525n laptop. These installation instructions have be made into 18 easy to follow printable steps. We have also create a video tutorial that shows you how to install your Dell Inspiron 1525n Palmrest.
Before you begin
Please take the time read the following safety guidelines when working on static sensitive electrical components. Dell repair manual service precautions
Tools needed for this laptop repair
1 x small phillips head screw driver
1 x small plastic scribe
Inspiron 1525n PalmrestInspiron 1525n Palmrest
Video tutorial repair manual
Installation and Removal Instructions Dell Inspiron 1525n Palmrest
Step 1
Remove the battery.
Step 2
Access Door
Unscrew the 8 screws holding the Access Door Cover.
Remove the cover, starting from right to left.
Step 3
Take out the (7) 2.5mm x 5mm screws.
Unscrew the (2) 2.5mm x 6mm screws that are holding the Touchpad Palm rest to the base.
Step 4
Power Button Cover
Remove two 2mm x 3mm screws that hold the 1525/1526 center control power button cover to the base of the computer.
Step 5
Turn the computer over (as if you were typing on it), and fully open the display (approximately 180 degrees, or as far as possible).
Lift and unsnap the 1525/1526 center control power button cover using a small flat head screw driver or a plastic scribe from the backside of the computer, from right to left. (Be very careful removing it because the plastic can be fragile. (Use caution lifting the power button cover off of the laptop, a cable is attached beneath it that can break easily.)
Step 6
Disconnect the media control cable under the power button cover and lift off the power button cover.
Step 7
Keyboard Removal
Unscrew the (2) 2.5mm x 5mmscrews above the keyboard and gently lift up the keyboard to reveal the ribbon cable. Be careful lifting the keyboard because it is very easy to cause damage to the ribbon cable or the motherboard connector. (If the motherboard connector breaks, it is very hard to find replacements for them without replacing the entire motherboard.)
Step 8
Lift the keyboard cable connector latch and remove the keyboard ribbon cable and keyboard.
Step 9
Bluetooth Card
Remove the Bluetooth card by unscrewing the 2mm x 3mm retaining screw.
Unplug the cable.
Slide the cable out and unhook it from the motherboard.
Step 10
LCD Display Assembly
Unplug the display cable from the motherboard.
Unplug the camera cable from the motherboard.
Step 11
Slide antenna wires out of the motherboard and loosen them from the top of the laptop.
Step 12
Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the left display hinge.
Unscrew the (2) 2.5mm x 3mm – 10 mm wafer hinge screws from the right display hinge.
Step 13
Lift the 1525/1526 LCD display assembly up away from the base.
Step 14
Power Button Circuit Board
Unplug the power button circuit board cable from the motherboard and lift the board off of the base. The power button board may have glue on it so be careful prying it up.
Step 15
Unplug the Speaker cable from the motherboard.
Step 16
Remove the remaining (2) 2.5mm x 5mm and the (1) 2.5mm x 3mm – 10mm wafer screws.
Step 17
Unplug the LED light cable.
Unplug the touchpad cable from the motherboard.
Step 18
Carefully lift the touchpad palmrest off of the base, starting from the upper left corner, unsnapping it along the edges.
Laptop & Tablet Parts
Desktop & All-in-one Parts
Dell Server Parts
Please take the time read the following safety guidelines when working on static sensitive electrical components.
