Dell Latitude 7410 2-In-1 How-To Install & Replace Your Palmrest Touchpad Assembly

By on July 19, 2024 · 4:49 pm
PrintEmail

In this Dell laptop tutorial we are going to show you how to install and replace the Palmrest Touchpad Assembly on your Latitude 7410 2-in-1 laptop. These installation instructions have been made into 19 easy to follow printable steps. We have also created a video tutorial that shows you how to install your Latitude 7410 2-in-1 Palmrest Touchpad Assembly.

Before you begin

Please take the time read the following safety guidelines when working on static sensitive electrical components.
Dell repair manual service precautions

Tools needed for this laptop repair

  • 1 x Phillips #0 screwdriver
  • 1 x Phillips #00 screwdriver
  • 1 x small plastic scribe
Latitude 7410 2-in-1 Palmrest Touchpad Ass

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Latitude 7410 2-in-1 Palmrest Touchpad Assembly

Video tutorial repair manual



Installation and Removal Instructions
Latitude 7410 2-in-1 Palmrest Touchpad Assembly

Before you begin: If you need help at any point, you can always contact Parts-People Repair Department for help with your diagnosis or repair.

Step 1

Unscrew the Bottom Base Cover (8 x captive screws).

Step 2

  • Unscrew the Bottom Base Cover (8 x captive screws).
  • Use a plastic scribe to pry apart and remove the Bottom Base Cover.
Unscrew the Bottom Base Cover (8 x captive screws).Use a plastic scribe to pry apart and remove the Bottom Base Cover.Unscrew the Bottom Base Cover (8 x captive screws).Unscrew the Bottom Base Cover (8 x captive screws).
Disconnect the battery cable.

Step 3

  • Disconnect the battery cable.
Disconnect the battery cable.Disconnect the battery cable.
Disconnect the speaker cable.

Step 4

  • Disconnect the speaker cable.
  • Remove the speakers.
Disconnect the speaker cable.Remove the speakers.Disconnect the speaker cable.
Remove the heat shield.

Step 5

  • Remove the heat shield.
Remove the heat shield.Remove the heat shield.
Unscrew and remove the Battery (4 x captive screws).

Step 6

  • Unscrew and remove the Battery (4 x captive screws).
Unscrew and remove the Battery (4 x captive screws).Unscrew and remove the Battery (4 x captive screws).
Unscrew and remove the antenna bracket (1 x 2mm x 2.5mm).

Step 7

  • Unscrew and remove the antenna bracket (1 x 2mm x 2.5mm).
  • Disconnect the antenna cables.
Unscrew and remove the antenna bracket (1 x 2mm x 2.5mm).Disconnect the antenna cables.Unscrew and remove the antenna bracket (1 x 2mm x 2.5mm).
Unscrew and remove the LCD bracket (2 x M2 x 2mm).

Step 8

  • Unscrew and remove the LCD bracket (2 x M2 x 2mm).
  • Disconnect the LCD cables.
Unscrew and remove the LCD bracket (2 x M2 x 2mm).Disconnect the LCD cables.Unscrew and remove the LCD bracket (2 x M2 x 2mm).Unscrew and remove the LCD bracket (2 x M2 x 2mm).
Unscrew the Cooling Fan (2 x 2mm x 2.5mm).

Step 9

Unclip the locking tab and disconnect the LED cable.

Step 10

  • Unclip the locking tab and disconnect the LED cable.
  • Unclip the locking tab and disconnect the touchpad cable.
Unclip the locking tab and disconnect the LED cable.Unclip the locking tab and disconnect the touchpad cable.Unclip the locking tab and disconnect the LED cable.Unclip the locking tab and disconnect the LED cable.
Unclip the locking tab and disconnect the USH board cable.

Step 11

  • Unclip the locking tab and disconnect the USH board cable.
Unclip the locking tab and disconnect the USH board cable.Unclip the locking tab and disconnect the USH board cable.
Unscrew and disconnect the F-Beam (2 x M2 x 2mm).

Step 12

  • Unscrew and disconnect the F-Beam (2 x M2 x 2mm).
Unscrew and disconnect the F-Beam (2 x M2 x 2mm).Unscrew and disconnect the F-Beam (2 x M2 x 2mm).
Unscrew and remove the I/O Circuit Board (1 x 2mm x 3.5mm) (1 x 2mm x 2.5mm).

Step 13

Unscrew and remove the I/O Circuit Board (1 x 2mm x 3.5mm) (1 x 2mm x 2.5mm).Unscrew and remove the I/O Circuit Board (1 x 2mm x 3.5mm) (1 x 2mm x 2.5mm).
Unclip the locking tabs and disconnect the keyboard cables.

Step 14

  • Unclip the locking tabs and disconnect the keyboard cables.
Unclip the locking tabs and disconnect the keyboard cables.Unclip the locking tabs and disconnect the keyboard cables.Unclip the locking tabs and disconnect the keyboard cables.Unclip the locking tabs and disconnect the keyboard cables.
Unscrew the left and right LCD hinges (4 x 2.5mm x 4mm).

Step 15

Unscrew the left and right LCD hinges (4 x 2.5mm x 4mm).Open the LCD Display Assembly and separate it from the Unscrew the left and right LCD hinges (4 x 2.5mm x 4mm).
Unscrew and remove the Motherboard (4 x

Step 16

Unscrew and remove the Motherboard (4 x Unscrew and remove the Motherboard (4 x
Unscrew and remove the power button (2 x 2mm x 2.5mm).

Step 17

  • Unscrew and remove the power button (2 x 2mm x 2.5mm).
Unscrew and remove the power button (2 x 2mm x 2.5mm).Unscrew and remove the power button (2 x 2mm x 2.5mm).
NOTE: USE A PHILLIPS #00 TO REMOVE THESE SCREWS:

Step 18

  • NOTE: USE A PHILLIPS #00 TO REMOVE THESE SCREWS:
  • Unscrew and remove the keyboard assembly (18 x 2mm x 2.5mm).
NOTE: USE A PHILLIPS #00 TO REMOVE THESE SCREWS:Unscrew and remove the keyboard assembly (18 x 2mm x 2.5mm).
The remaining piece is the Palmrest Touchpad Assembly.

Step 19

Latitude 7410 2-in-1 Palmrest Touchpad Ass

Dell Laptop Replacement Parts Needed

DIY Discount - Parts-People.com offers 5% off to all DO-IT-YOURSELFERS!
Use this coupon code to save 5% off these parts
DIYM514
Latitude 7410 2-in-1 Palmrest Touchpad Assembly

Topics: Dell Latitude Repair Manuals Dell Laptop Repair Dell Repair Manuals Latitude 7410 2-In-1 Palmrest Touchpad Assembly

Tags

Join the conversation!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.